Search found 24 matches
- Sun Jun 12, 2022 8:25 pm
- Forum: Tech Forum
- Topic: megasquirt and m30b35 vr setup
- Replies: 0
- Views: 5454
megasquirt and m30b35 vr setup
I've sucessfully gotten my m106 to run using the 60-2 setup from an m30b35, but I'm having high rpm breakup. I've installed an 10k resistor in line, and played with the pots r52 and r56. I've got the vr pickup set at .020" clearance. Previously, I had it set at .030", but couldn't get it t...
- Thu Sep 09, 2021 8:10 pm
- Forum: Tech Forum
- Topic: Need some electrical help...turn signal flasher indicator.
- Replies: 4
- Views: 1321
Re: Need some electrical help...turn signal flasher indicator.
I know when I put led lights in they would not flash. I had to have a regular bulb on each side to get it to flash. Must be a pull up thing.
- Sun Jul 18, 2021 8:17 pm
- Forum: Tech Forum
- Topic: sideloader lsd diff rebuild?
- Replies: 2
- Views: 1133
Re: sideloader lsd diff rebuild?
Thanks Jeff, I bought the seals and 3 clutch plate sets, using porsche dogear plates. I'm going to go with factory spec(0.2mm) on clearance with the extra plates installed. I'm considering more ramp angle on acceleration ramp(maybe go 30*) for more drive locking.
- Mon Jun 28, 2021 9:05 pm
- Forum: Tech Forum
- Topic: sideloader lsd diff rebuild?
- Replies: 2
- Views: 1133
sideloader lsd diff rebuild?
I need to rebuild my sideloader lsd diff. I'd like to get more lock up. Anyone have experience with this? I'm thinking I can shim it for more initial break away torque, but I'm unsure how much to shim it. any help appreciated!
- Wed Jun 21, 2017 7:45 pm
- Forum: Tech Forum
- Topic: brake caliper problem
- Replies: 7
- Views: 3620
I do use a line wrench and still managed to mess up 1 of the steel line nuts, so I start looking at the wrench and realize there is a chamfer on the inside that misses the lower half on the nut. I ground the wrench to eliminate the chamfer and get full contact on the nut. The rest of the lines came ...
- Tue Jun 20, 2017 6:47 pm
- Forum: Tech Forum
- Topic: brake caliper problem
- Replies: 7
- Views: 3620
Well it turned out to be the rubber brake hose. I've heard of this before, but kinda thought it was urban legend. The hose shows no sign of problem on the outside but even 120 psi won't pass thru. So this time I'll get s.s. braided lines. What a pita job! I remember when I first resurrected this car...
- Mon Jun 19, 2017 7:28 pm
- Forum: Tech Forum
- Topic: brake caliper problem
- Replies: 7
- Views: 3620
!.
Update and correction I was wrong about cracking the bleeder because these 4 pots have 2 cicuits and 3 bleeders, so now I have learned the lower pucks are on a different circuit and when I crack the lower bleeder it 's instantly free to move. I decided to pressure bleed again starting on passenger f...
- Sat Jun 17, 2017 6:26 pm
- Forum: Tech Forum
- Topic: brake caliper problem
- Replies: 7
- Views: 3620
brake caliper problem
My 79 euro 645 has 4 pot ate calipers on the front, with a vacumn booster.I had a problem with the driver front caliper sticking and dragging , getting hot, so I replaced them with rebuilt calipers. Now I've got the same problem. Even a short drive is enough to cause the wheel to drag causing a shim...
- Thu Aug 06, 2015 7:04 pm
- Forum: Tech Forum
- Topic: Turn Off and remove the key...power stays on
- Replies: 4
- Views: 3075
- Fri Feb 08, 2013 5:58 pm
- Forum: Tech Forum
- Topic: bad valve stem seal
- Replies: 3
- Views: 2341
hallelujah! It was the coil high tension wire shorting out to the chassis. I was really getting depressed. I just don't want to have to pull the motor again. I still don't understand why #3 was the one that kept fouling, or how it ran at all as the wire was really toasted, right where I couldn't see...
- Thu Feb 07, 2013 8:13 pm
- Forum: Tech Forum
- Topic: bad valve stem seal
- Replies: 3
- Views: 2341
bad valve stem seal
I've got a bad #3 plug that keeps fouling on my 84 m106. I think it may be the valve stem seals. Does anyone know if it's possible to move rockers and change seals with the head on in the car?
tia
marc
tia
marc
- Sat Dec 04, 2010 9:02 pm
- Forum: Tech Forum
- Topic: head gasket question
- Replies: 9
- Views: 5037
- Sat Nov 20, 2010 9:38 pm
- Forum: Tech Forum
- Topic: how to improve sideloader lsd lockup
- Replies: 4
- Views: 3184
- Mon Nov 08, 2010 7:56 pm
- Forum: Tech Forum
- Topic: how to improve sideloader lsd lockup
- Replies: 4
- Views: 3184
how to improve sideloader lsd lockup
Hi,
I have an early 6 series euro w a sideloader lsd.
does anyone know if it can be rebuilt and improve lockup by adding extra metal &/ or friction plates?
seems like 1 or 2 extra metal plates would help, but I'd love to hear from someone who's done it before.
thanks
marc
I have an early 6 series euro w a sideloader lsd.
does anyone know if it can be rebuilt and improve lockup by adding extra metal &/ or friction plates?
seems like 1 or 2 extra metal plates would help, but I'd love to hear from someone who's done it before.
thanks
marc
- Thu Oct 14, 2010 6:55 pm
- Forum: Tech Forum
- Topic: re: no start
- Replies: 0
- Views: 2580
re: no start
start with basics
are you gettng spark?
using a cheap noid light, are you getting injector pulse?
are you getting fuel pressure?
good luck
marc
are you gettng spark?
using a cheap noid light, are you getting injector pulse?
are you getting fuel pressure?
good luck
marc