Search found 14 matches
- Fri May 10, 2024 4:10 am
- Forum: Tech Forum
- Topic: multi-layered sheet metal
- Replies: 4
- Views: 79
Re: multi-layered sheet metal
Ok, I dropped the carrier and here`s what I think is going on; - Layer # 1 in your pics is the floorpan. When wire brushing you will find a foam gasket between the floorpan and the guide bushing for the threaded rod. That said, the floorpan does not add any structural strength to the mounting point....
- Wed May 01, 2024 11:36 am
- Forum: Tech Forum
- Topic: multi-layered sheet metal
- Replies: 4
- Views: 79
Re: multi-layered sheet metal
Will do. Plan is somewhere next week but in reality, my plans don`t always work... :roll: My main concern would be keeping that rod in position. It all depends on what quality level of repair you`re after. If you want to patch the pitted panel, the whole bunch needs to come out, probably including t...
- Mon Apr 29, 2024 7:06 am
- Forum: Tech Forum
- Topic: multi-layered sheet metal
- Replies: 4
- Views: 79
Re: multi-layered sheet metal
I`m a couple days away from dropping my rear subframe, so I will have a closer look at the construction of that area. From what I could see on mine after clearing some ubc I could reach, there is no 3rd layer. Mine is a `76 series 1 528, so there might have been an upgrade in that section..? Or mayb...
- Wed Apr 24, 2024 2:13 am
- Forum: Tech Forum
- Topic: Water control valve replacement - HVAC removal?
- Replies: 6
- Views: 173
Re: Water control valve replacement - HVAC removal?
ok, thanks.
I `ve had one fail in a hurry while doing 80mph... That indoor coolant and outdoor winter weather resulted in zero visibility within a second. That was kinda scary to say the least.
I `ve had one fail in a hurry while doing 80mph... That indoor coolant and outdoor winter weather resulted in zero visibility within a second. That was kinda scary to say the least.
- Tue Apr 23, 2024 7:40 am
- Forum: Tech Forum
- Topic: Water control valve replacement - HVAC removal?
- Replies: 6
- Views: 173
Re: Water control valve replacement - HVAC removal?
just wondering... where did you find a valve..? My non air 76 is mostly in pieces but the dash and heater are still in. I have no leaks but I thought about replacing the valve and core now... I have not seached very hard yet but it seemed the valve it no longer produced.
- Fri Apr 19, 2024 7:26 am
- Forum: Tech Forum
- Topic: replacing hard fuel lines
- Replies: 3
- Views: 323
Re: replacing hard fuel lines
ah, the good old reliable can of wurms...
- Fri Apr 19, 2024 3:08 am
- Forum: Tech Forum
- Topic: replacing hard fuel lines
- Replies: 3
- Views: 323
Re: replacing hard fuel lines
In the front ,the lines are just clamped to the side of the framerail right below where they go through the inner fender. I think you will find biggest challenge where they pass the rear subframe / diff. My 528 is all in pieces , but don`t know how I would fix that without dropping the frame...
- Sat Apr 06, 2024 5:23 pm
- Forum: Tech Forum
- Topic: Brake bleed screw size?
- Replies: 5
- Views: 248
Re: Brake bleed screw size?
Is there no dealership in your area? those were also used on e28 , 24 ,23 and some more.
- Mon Mar 25, 2024 3:19 pm
- Forum: Tech Forum
- Topic: Power steering pump - again.
- Replies: 1
- Views: 223
Re: Power steering pump - again.
That could cause pulling the pump out of alignment. Becomes a problem when it throws the belt and you suddenly have to corner with no ps.
- Thu Feb 01, 2024 2:12 am
- Forum: Tech Forum
- Topic: Brake booster one way check valve?
- Replies: 3
- Views: 807
Re: Brake booster one way check valve?
I`d look into frozen calipers.
- Tue Dec 19, 2023 7:19 am
- Forum: Tech Forum
- Topic: Starter Bosch sr441x
- Replies: 22
- Views: 3970
Re: Starter Bosch sr441x
I was thinking the same... bad starter or missing teeth on the flywheel? Try pushing the car forward in gear so the position of the flywheel changes. Easy check to be sure the flywheel is ok.
- Thu Dec 14, 2023 2:00 am
- Forum: Tech Forum
- Topic: max 14" tire size?
- Replies: 3
- Views: 2149
Re: max 14" tire size?
I will stick to the 205/70. Still lots of decent tires to chose from overhere. I looked into the 225/60 but that a smaller diameter so no go. Also, it looks like there`s only 2 brands to choose from. I had the Alpina`s checked for straightness yesterday and 1 seemed ok-ish, so that`s good :shock: Th...
- Mon Dec 11, 2023 5:31 pm
- Forum: Tech Forum
- Topic: max 14" tire size?
- Replies: 3
- Views: 2149
max 14" tire size?
hey everyone, Newbee here from europe. I`m currently restoring my `76 528. I purchased a set of 7j x 14" Alpina alloys. Ride height will be factory and I like the fenders filled. The factory size tire would have been 195/70 and 205/70 will work just fine but what would be the max size to run wi...
- Thu Nov 09, 2023 5:27 pm
- Forum: Tech Forum
- Topic: ATF leak at speedo drive
- Replies: 5
- Views: 2498
Re: ATF leak at speedo drive
Hi there, Not sure if your problem has been fixed yet , but I`d visit the local bmw dealer and just ask for that size o-ring Looks like the ones you need are 19x1.8 mm. That size is pretty common overhere in Europe and it`s also used on the 120i and I`m sure many more bmw`s.